<div dir="auto">Another repeater to try would be N1LHP 146.835 PL 77.0 in Andover</div><div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Sep 20, 2024 at 7:37 PM Matt Wagner <<a href="mailto:mwaggy@gmail.com">mwaggy@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;padding-left:1ex;border-left-color:rgb(204,204,204)"><div>On Fri, Sep 20, 2024 at 16:38 Steven Ford <<a href="mailto:stevef136@gmail.com" target="_blank">stevef136@gmail.com</a>> wrote:<br></div><div><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;padding-left:1ex;border-left-color:rgb(204,204,204)"><div dir="ltr">I have a Yaetsu FT -65 and this is how I programmed it.<div><br></div><div>Receive Frequency  Transmit Frequency      Offset Frequency        Offset Direction        Auto Repeater   Operating Mode  Name    Tone Mode       CTCSS   Rx CTCSS        DCS     Rx DCS  Skip    Step    Tx Power        Bank 1  Bank 2  Bank 3  Bank 4  Bank 5  Bank 6  Bank 7  Bank 8  Bank 9  Bank 10 Comment<br> 146.95500    146.35500       600 kHz Minus   1       FM      BILL2   T-Tone  74.4 Hz 100.0 Hz        023     023     0       Auto    High           </div></div></blockquote><div dir="auto"><br></div><div dir="auto">My email client shows this as a confusing jumble. I think what you have is correct, but I would change whatever is 100.0 Hz to 74.4 Hz.</div><div dir="auto"><br></div><div dir="auto">You need 74.4 Hz on transmit to get into the repeater. You can optionally require it on receive because the repeater also transmits a 74.4 Hz tone. There is another repeater on 146.955 on Cape Cod which you might hear otherwise when propagation is good: <div><a href="https://barnstablearc.org/?q=node/7" target="_blank">https://barnstablearc.org/?q=node/7</a></div><div dir="auto"><br></div><div dir="auto">I <i>think</i> you have 74.4 for transmit which is what you need, and 100.0 for receive which is wrong but irrelevant if “T-Tone” is used? Just want to make sure it’s not the other way around, because a 100.0 Hz tone won’t open squelch on the repeater.</div><div dir="auto"><br></div></div><div dir="auto"><br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;padding-left:1ex;border-left-color:rgb(204,204,204)"><div dir="ltr"><div dir="auto">I can hear everyone most of the time but when I transmit I am not getting through. I have called QSO a few times over the last 2 days to no response. </div></div></blockquote><div dir="auto"><br></div><div dir="auto">I suspect a handheld radio from your location is just not strong enough to get into the repeater.</div><div dir="auto"><br></div><div dir="auto">Per the presentation linked from <div dir="auto"><a href="http://www.wb1gof.org/repeaters/" target="_blank">http://www.wb1gof.org/repeaters/</a> the repeater is putting out 55 Watts. Compared to your HT’s 5ish Watts, you will hear it a lot better than it hears you.</div><div dir="auto"><br></div><div dir="auto">I agree with what others said; a better/higher antenna can make a big difference, and you might benefit from trying some repeaters closer to you to confirm all is well with your radio, if you haven’t already. There are 2 Meter repeaters with good range in North Reading (KC1US), Topsfield (N1HSY), and Danvers (NS1RA).</div><div dir="auto"><br></div><div dir="auto">For what it’s worth I live in Lowell and use a 50W mobile radio in the shack to get into the Westford repeater. I wouldn’t expect great results from my QTH (which is at a low elevation) from an HT.</div></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;padding-left:1ex;border-left-color:rgb(204,204,204)"><div dir="ltr"><div dir="auto"></div></div></blockquote></div></div>
_______________________________________________<br>
bars mailing list<br>
<a href="mailto:bars@w1hh.org" target="_blank">bars@w1hh.org</a><br>
<a href="http://mail.w1hh.org/mailman/listinfo/bars_w1hh.org" rel="noreferrer" target="_blank">http://mail.w1hh.org/mailman/listinfo/bars_w1hh.org</a><br>
</blockquote></div></div>